P22 not Feeding properly - Page 3 - WaltherForums
WaltherForums
 

Go Back   WaltherForums > Walther Firearms > Walther Rimfire & CO2 Pistols

Like Tree2Likes
Reply
 
LinkBack Thread Tools Display Modes
Old 01-07-2017, 11:58 PM   #21
Junior Member
 
Join Date: Jan 2017
Posts: 4
rkdd4 .22
Having same feeling problem

Every second round is not feeding unless manually done. Both magazines do this. After second round every other round feeds. Tried different ammo same thing occurs.Have about 500 rounds through gun with no problems till today.Any suggestions would be very helpful
rkdd4 is offline   Reply With Quote
Register
Old 01-10-2017, 07:47 PM   #22
Junior Member
 
Join Date: Jan 2017
Posts: 3
Sd790 .22
I have been fighting the same issue for a while now. I've been lurking this forum quite a bit and thought that these pictures might help. I've tried different ammo but the second round almost always has a ftf. After I took these pictures, I could see that the crimp is getting hung up on the bottom of the feed ramp. I gently rounded it off with some 800 grit sandpaper, but it didn't help at all.

Any suggestions?


Sd790 is offline   Reply With Quote
Old 01-11-2017, 10:32 PM   #23
Junior Member
 
Join Date: Jan 2017
Posts: 3
Sd790 .22
I got brave with 320 grit sandpaper then finally with the dremel to reduce the hammer friction on the bottom of the slde. I had already worked the feed ramp a bit with no change. Once the hammer was visibly ground down, I polished it with some 800 grit. My last 3 magazines fed flawlessly! I've never had a magazine run through without at least one ftf before today, so it's quite a relief to finally see it run like a real gun.
Sd790 is offline   Reply With Quote
 
Old 01-14-2017, 08:49 PM   #24
Senior Member
 
Join Date: Feb 2009
Location: Indian Springs, AL
Posts: 6,981
1917-1911M .38
Man, this is an old thread. The real P22 section is up a couple of spots on the homepage. Yep the hammer can catch in the notch between the rear of the breech block and safety drum and the hardest round friction wise for the slide to shove out of the mag is the top on with a fully loaded mag or even with 9 rounds present. As the stack goes down less energy is required to strip and chamber a round. A .22 recoil spring can't be very strong so it is important that nothing hang up the slide and that good lubricants be used. I prefer dry moly powder myself and no oil 1917
1917-1911M is offline   Reply With Quote
Old 02-02-2017, 08:36 PM   #25
dsk
Senior Member
 
Join Date: Jul 2014
Posts: 383
dsk .22
My P22 ran way better after I polished the face of the hammer. Before it would fail to cycle about half the time with Federal Auto Match, but after polishing it runs with that ammo about 95% of the time. CCI high- or hyper- velocity is still the most trouble-free however.

Last edited by dsk; 04-26-2017 at 11:25 PM. Reason: typo
dsk is offline   Reply With Quote
Old 02-02-2017, 10:45 PM   #26
Senior Member
 
tattooo's Avatar
 
Join Date: Aug 2016
Posts: 136
tattooo .22
I polished the fredramp with flitz and it feeds like butter now.
tattooo is offline   Reply With Quote
Old 02-14-2017, 05:53 PM   #27
Super Moderator
 
UniversalExports's Avatar
 
Join Date: Sep 2009
Location: El Paso, Texas
Posts: 9,163
UniversalExports .38
Rather than resurrecting a thread that's just shy of 14 years since it saw its last post, might I suggest you start a new thread in the dedicated P22 Forum? You might get more activity and current information.
1917-1911M and Pilotsteve like this.
__________________
Universal Exports

The Globe is a ship that has everything—
Including a serial killer with a large knife
and a penchant for the rich and beautiful.

Visit me at my Blog and on Facebook
UniversalExports is offline   Reply With Quote
Old 03-01-2017, 04:48 PM   #28
Supporting Member
 
Join Date: May 2007
Location: Backwoods Virginia
Posts: 11,700
MGMike .38
Why bother? He'll find it was a POS in 2003, and nothing has changed.

M
MGMike is offline   Reply With Quote
Old 03-02-2017, 08:38 AM   #29
Junior Member
 
Join Date: Jan 2017
Posts: 4
rkdd4 .22
POS? Just clean and lube it up good. Use the right ammo and you will be fine.Its only a $250 dollar gun for target and plinking. Use CCI mini mags and you will be jubilant.
rkdd4 is offline   Reply With Quote
Reply

Lower Navigation
Go Back   WaltherForums > Walther Firearms > Walther Rimfire & CO2 Pistols


Search tags for this page
p 22 not feeding
,
p22 failure to feed
,
walther p22 failure to eject
,

walther p22 failure to feed

,
walther p22 failure to feed fix
,
walther p22 feeding problems
,
walther p22 ftf fix
,
walther p22 issues
,

walther p22 not feeding

,
walther p22 problems
,
walther p22 problems feeding
,
walther p22 will not feed
Click on a term to search for related topics.

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On





Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.